*****************************************************
* 10/100Mbps Fast Ethernet USB Adapter Installation *
*****************************************************

Contents:

  System Requirements
  Hardware Installation
  Software Installation

----------------------------
System Requirements
----------------------------
One of the following operating systems is required:

  Windows Me
  Windows 2000
  Windows 98 or Windows 98 Second Edition

----------------------
Hardware Installation
----------------------
The Fast Ethernet USB  Adapter comes with a USB cable. One end of the cable
has a rectangular plug, which is called an A-type connector. The other
end of the cable has a square plug, or B-type connector.

The adapter has two ports. One is for Twisted Pair cabling -- it
looks like an over-sized phone jack. The other port looks like a
square hole -- this is the USB B-type port.

 1. Make sure your PC is powered on and that you are at the Windows 98
    desktop.

 2. Insert the cable's square B-type plug into the adapter's B-type
    port.

 3. Insert the other end of the USB cable (the A-type connector) into
    the USB port on your PC. The adapter is now connected to your PC.

 4. Connect your adapter to a 10Mbps or 10/100Mbps Ethernet adapter or
    10/10Mbps Ethernet hub/switch using RJ-45 Twisted Pair cabling.
    The RJ-45 jacks should fit into the RJ-45 port on both of the adapter
    and hub/switch.


----------------------
Software Installation
----------------------
Driver installation procedures vary for each operating system.
The following operating systems are supported:

  Windows Me
  Windows 2000
  Windows 98


Windows Me
-----------
Follow the procedures below to install the 10/100Mbps Fast Ethernet USB
Adapter's driver:

 1. Windows will automatically detect the 10/100Mbps Fast Ethernet USB
    Adapter when it is connected to your computer.

 2. The Add New Hardware Wizard will indicate that it has found
    "10/100 Fast Ethernet".  Click Next to continue.

 3. Insert the 10/100Mbps Fast Ethernet USB Adapter driver disc into
    your Floppy disk drive.

 4. Select Specify the location of the driver (Advanced) and click Next.

 5. Select Specify a Location and type or browse to the "A:\",
    and then click Next.  If prompted for additional Windows files,
    insert your Windows Me CD-ROM and click Next.

 6. Click Finish.

 7. When asked to restart the computer,click Yes to activate the
    10/100Mbps Fast Ethernet USB Adapter.


Windows 2000
-------------
Follow the procedures below to install the 10/100Mbps Fast Ethernet USB
Adapter's driver:

 1. Windows will automatically detect the 10/100Mbps Fast Ethernet USB
    Adapter when it is connected to your computer.

 2. The Found New Hardware message will appear, followed by
    the Found New Hardware Wizard dialog. Click Next.

 3. On the Install Hardware Device Drivers screen, the 10/100Mbps
    Fast Ethernet USB Adapter will be identified as "10/100 Fast Ethernet"
    and click Next.

 4. Insert the 10/100Mbps Fast Ethernet USB Adapter driver disc into your
    Floppy disk drive.

 5. Select Search for a suitable driver for my device (recommended) and
    click Next.

 6. On the Locate Driver Files screen, select the Specify a location and
    click Next.

 7. In response to the message "Insert the manufacturer's installation
    disk...," insert the 10/100Mbps Fast Ethernet USB Adapter driver disk
    and type or browse to "A:\" on the 10/100Mbps Fast Ethernet USB Adapter
    driver disk, and then click OK. If prompted for additional Windows
    files, insert your Windows 2000 compact disc and click Next.

 8. On the Driver Files Search Results screen, click Next again to install
    the driver displayed. On the next screen, click Finish.

 9. When asked to restart the computer,click Yes to activate the 10/100Mbps
    Fast Ethernet USB Adapter.


Windows 98
-----------
Follow the procedures below to install the 10/100Mbps Fast Ethernet USB
Adapter's driver:

 1. Windows will automatically detect the 10/100Mbps Fast Ethernet USB
    Adapter when it is connected to your computer.

 2. The Add New Hardware Wizard will indicate that it has found
    "10/100 Fast Ethernet". Click Next to continue.

 3. Insert the 10/100Mbps Fast Ethernet USB Adapter driver disk into
    your Floppy disk drive.

 4. Select Search For Best Driver and click Next.

 5. Select Specify A Location and type or browse to the "A:\" on 10/100Mbps
    Fast Ethernet USB Adapter driver disk, and then click Next. If prompted
    for additional Windows files, insert your Windows 98 CD-ROM and
    click Next.

 6. Click Finish.

 7. When asked to restart the computer,click Yes to activate the
    10/100Mbps Fast Ethernet USB Adapter.
